We ship !

We are not shipping goods to USA
except BioBeam 940

How To Use

 

Recommended illumination is 1-2 times a day, six-seven minutes on each infected area.

The device is lightweight and portable while an optional extension arm can be used to make the treatment "hands free."
 

Usage Instructions

(numbers in parentheses refer to drawing)  
1. Plug the AC adaptor (6) into the BioBeam 660 device using the plug (1) at the end of the cord (a round plug with a hole in the middle). Do not use any other power supply.
Important:
Use only the power AC adaptor supplied by the BioBeam 660 manufacturer.

2. Make sure the operation switch (2) is in the OFF position.

3. Plug the AC adaptor into the correct voltage wall outlet (see voltage indicated on the AC adaptor).
 

Warning

:
Keep light away from eyes during use.
4. Hold the instrument at a distance of 2.5-3 cm from the treated area, for coverage of an area approximately 2-3 cm in diameter. Each area of this size should be illuminated for 6-8 minutes. Treatments are recommended twice a day.  The instrument can be kept at the correct distance from the face by use of the enclosed ring (5) which should be touching the face.
5. To operate, move the operation switch (2) to the CW position.
A green indicator light (3) lights up while the BioBeam 660 in use, signifying that the device is working properly. If this indicator light begins to blink, the BioBeam 660 is not working properly and must be taken in for servicing.
6. After treatment is completed, move the operation switch (2) to OFF and only then remove the AC adaptor (8) from the wall outlet.
7. Flexible extension arm:
The arm is sold separately in its own package. The flexible extension arm allows "hands off" treatment of hard-to-reach areas (such as the back).
 

   
Technical Specifications

 

 

Wavelength

630 nm

Beam area at focus

2 cm2

Continuous Wave (CW)

Total light Power

65 mW

Power density at focus

18 mW/cm2

Pulse wave

Total peak light power at focus

210 mW

Peak power at focus (typical)

60 mW/cm2

Frequency (typical)

130 Hz

Duty ratio (typical)

10%

Total Average power at focus

21 mW

Power Requirements

Input voltage

100-240V AC

Line frequency

50-60 Hz

 

 

CAUTION & WARNING


1. Keep device away from children.
2. Keep your eyes protected during treatment, do not look directly into the light source.
3. Use only the power adaptor supplied by the BioBeam 660 manufacturer.
4. Use of the device in the manner described above does not in any way guarantee successful treatment.
5. BioBeam 660 is not intended to be a replacement or a substitute for medical treatment by your health care provider. Should there be no improvements after 30 days of using the BioBeam 660, please consult your physician. If the diagnosis of your physician conforms with the BioBeam 660’s intended applications, then it is safe to continue using the BioBeam 660 until full recovery.

How To Use

 

Recommended illumination is 1-2 times a day, six-seven minutes on each infected area.

The device is lightweight and portable while an optional extension arm can be used to make the treatment "hands free."
 

Usage Instructions

(numbers in parentheses refer to drawing)  
1. Plug the AC adaptor (6) into the BioBeam 660 device using the plug (1) at the end of the cord (a round plug with a hole in the middle). Do not use any other power supply.
Important:
Use only the power AC adaptor supplied by the BioBeam 660 manufacturer.

2. Make sure the operation switch (2) is in the OFF position.

3. Plug the AC adaptor into the correct voltage wall outlet (see voltage indicated on the AC adaptor).
 

Warning

:
Keep light away from eyes during use.
4. Hold the instrument at a distance of 2.5-3 cm from the treated area, for coverage of an area approximately 2-3 cm in diameter. Each area of this size should be illuminated for 6-8 minutes. Treatments are recommended twice a day.  The instrument can be kept at the correct distance from the face by use of the enclosed ring (5) which should be touching the face.
5. To operate, move the operation switch (2) to the CW position.
A green indicator light (3) lights up while the BioBeam 660 in use, signifying that the device is working properly. If this indicator light begins to blink, the BioBeam 660 is not working properly and must be taken in for servicing.
6. After treatment is completed, move the operation switch (2) to OFF and only then remove the AC adaptor (8) from the wall outlet.
7. Flexible extension arm:
The arm is sold separately in its own package. The flexible extension arm allows "hands off" treatment of hard-to-reach areas (such as the back).
 

   
Technical Specifications

 

 

Wavelength

630 nm

Beam area at focus

2 cm2

Continuous Wave (CW)

Total light Power

65 mW

Power density at focus

18 mW/cm2

Pulse wave

Total peak light power at focus

210 mW

Peak power at focus (typical)

60 mW/cm2

Frequency (typical)

130 Hz

Duty ratio (typical)

10%

Total Average power at focus

21 mW

Power Requirements

Input voltage

100-240V AC

Line frequency

50-60 Hz

 

 

CAUTION & WARNING


1. Keep device away from children.
2. Keep your eyes protected during treatment, do not look directly into the light source.
3. Use only the power adaptor supplied by the BioBeam 660 manufacturer.
4. Use of the device in the manner described above does not in any way guarantee successful treatment.
5. BioBeam 660 is not intended to be a replacement or a substitute for medical treatment by your health care provider. Should there be no improvements after 30 days of using the BioBeam 660, please consult your physician. If the diagnosis of your physician conforms with the BioBeam 660’s intended applications, then it is safe to continue using the BioBeam 660 until full recovery.

 

 

$179.95

 

 

 

$179.95