We ship !

We are not shipping goods to USA
except BioBeam 940

How to use

 

Manual Instructions, Treatment Methodology & Protocol    

1. Plug the BioBeam AC adapter (6) into the BioBeam 940 using the plug at the end of the adapter cord (1).

2. Make sure the power switch is set to OFF.

3. Plug the AC adapter into a wall outlet, matching the voltage indicated on the AC adapter.

4. To operate, switch the power switch (2) to the CW or PULSE position. PULSE mode supplies increased power, allowing for deeper penetration. In general, the duration of treatment is between 5 and 30 minutes in CW mode followed by an additional 5 to 30 minutes in PULSE mode. A green indicator light (3) is illuminated when the power is on and the BioBeam 940 is operating properly. If the green indicator light begins to blink, the BioBeam 940 is not working properly and requires servicing.

5. In order to direct the maximum intensity of light rays on the area to be treated, adjust the distance between the skin and the BioBeam 940 so that a minimal area is illuminated in red. Focus the light source properly on the area of skin to be treated. In order to focus the light beam correctly, make use of the spacer ring (5). Place the spacer ring on the light source (4) and then place the ring on the area of skin to be treated.

6. After treatment is completed, move the power switch to the OFF position and remove the AC adapter from the wall outlet.

 

Treatment Instructions         


1. Treat each area for 5 to 30 minutes in CW mode, followed by another 5 to 30 minutes in PULSE mode. Treatment may be repeated up to three times daily, at intervals of at least four hours. In general, treatments are applied in the morning and evening. Satisfactory results have also have been achieved when only one daily treatment was applied.          
2. If the case has been classified as chronic, the treatment period will be longer. Other measures may be needed, such as muscle building and exercise.
3. For the small joints of the hands and feet, apply a short, 10 to 20 minute treatments; for the knees, 20 to 30 minutes; and for the back, 30 to 60 minutes

Treatment Methodology & Protocol


The following treatment instructions are based on the accumulated clinical experience gained over several years of use in the physiotherapy department of Bnei Zion Hospital in Haifa, Israel. Hundreds of orthopedic and rheumatic disorders were successfully treated over this period.

read more...

 

BioBeam 940 Accessories 


The following accessories are recommended for use with the BioBeam 940 in order to facilitate use in hard-to-reach areas, or in the case of physical limitations or handicaps.

1. Spacer ring (5)

The spacer ring fits directly on to the BioBeam 940 light source (4) and is used to help focus the light beam by maintaining the correct distance between the BioBeam and the treated area.


2. Elastic Straps - The elastic straps frees the user from holding the BioBeam 940 in his/her hand and allows the user to reach hard-to-reach areas such as the back or lower shoulders.

Important:

  • Keep the BioBeam 940 out of reach of children.
  • Do not look directly at the light source.
  • Only use the power adapter supplied with your BioBeam 940.
  • These instructions in no way represent a guarantee for successful treatment.

 

How to use

 

Manual Instructions, Treatment Methodology & Protocol    

1. Plug the BioBeam AC adapter (6) into the BioBeam 940 using the plug at the end of the adapter cord (1).

2. Make sure the power switch is set to OFF.

3. Plug the AC adapter into a wall outlet, matching the voltage indicated on the AC adapter.

4. To operate, switch the power switch (2) to the CW or PULSE position. PULSE mode supplies increased power, allowing for deeper penetration. In general, the duration of treatment is between 5 and 30 minutes in CW mode followed by an additional 5 to 30 minutes in PULSE mode. A green indicator light (3) is illuminated when the power is on and the BioBeam 940 is operating properly. If the green indicator light begins to blink, the BioBeam 940 is not working properly and requires servicing.

5. In order to direct the maximum intensity of light rays on the area to be treated, adjust the distance between the skin and the BioBeam 940 so that a minimal area is illuminated in red. Focus the light source properly on the area of skin to be treated. In order to focus the light beam correctly, make use of the spacer ring (5). Place the spacer ring on the light source (4) and then place the ring on the area of skin to be treated.

6. After treatment is completed, move the power switch to the OFF position and remove the AC adapter from the wall outlet.

 

Treatment Instructions         


1. Treat each area for 5 to 30 minutes in CW mode, followed by another 5 to 30 minutes in PULSE mode. Treatment may be repeated up to three times daily, at intervals of at least four hours. In general, treatments are applied in the morning and evening. Satisfactory results have also have been achieved when only one daily treatment was applied.          
2. If the case has been classified as chronic, the treatment period will be longer. Other measures may be needed, such as muscle building and exercise.
3. For the small joints of the hands and feet, apply a short, 10 to 20 minute treatments; for the knees, 20 to 30 minutes; and for the back, 30 to 60 minutes

Treatment Methodology & Protocol


The following treatment instructions are based on the accumulated clinical experience gained over several years of use in the physiotherapy department of Bnei Zion Hospital in Haifa, Israel. Hundreds of orthopedic and rheumatic disorders were successfully treated over this period.

read more...

 

BioBeam 940 Accessories 


The following accessories are recommended for use with the BioBeam 940 in order to facilitate use in hard-to-reach areas, or in the case of physical limitations or handicaps.

1. Spacer ring (5)

The spacer ring fits directly on to the BioBeam 940 light source (4) and is used to help focus the light beam by maintaining the correct distance between the BioBeam and the treated area.


2. Elastic Straps - The elastic straps frees the user from holding the BioBeam 940 in his/her hand and allows the user to reach hard-to-reach areas such as the back or lower shoulders.

Important:

  • Keep the BioBeam 940 out of reach of children.
  • Do not look directly at the light source.
  • Only use the power adapter supplied with your BioBeam 940.
  • These instructions in no way represent a guarantee for successful treatment.

 

 

 

$179.95

 

 

 

$179.95